Zinak AQM53 Antifouling Paint Technical Data Sheet Product Description : A premium strength, TBT free, two component, cuprous oxide antifouling with AQM Technology. Offers superior protections in high fouling conditions. * Extended launching times * Easy application * Quick drying Recommended Usage : Zinak AQM53 Antifouling Paint is recommended for fiberglass, wood and primed underwater metals (except aluminum) at Newbuilding or Maintenance Repair. Technical Data Generic Type: Epoxy Polyamide Flash Point: 20°C (68°F) Volume Solids % : 60 Specific Gravity : Base 1.465 kg/liter – Hardener 0.9 kg/liter Gloss level: Semi Glossy Dry Film Thickness: 50 micron/coat Wet Film Thickness: 90 micron/coat Theoretical Coverage: 80 to 100 sq.fit/Ltr/coat(50 micron)** Recoating Period: 6 to 8 Hrs Approximate Drying Time @ 20°C/68° F: Surface dry: 1 hrs, Hard dry: 5 hrs, Full Cure: 7 days Mixing Ratio: Part A 3: Part B 1 by volume (Base: Hardener) Recommended Thinner: Hollywood Antifouling Epoxy Thinner Thinning Ratio: Airless Spray (5%), Air Spray (10%), Brush/Roller (5%) Do not thin unless absolutely necessary. Pot Life: 6 to 8 Hrs Shelf Life: 2 year from date of manufacture original tightly closed container away from direct sunlight and excessive heat. Mechanical stirring may be necessary before usage. Method of application: Airless spray, Air Spray, Brush or Roller. ** Actual covering capacity may vary depending upon the surface condition, temperature, wind velocity, application skill, surface roughness, surface porosity and shade to shade. Surface Preparation: Remove oil and grease etc. thoroughly with a suitable detergent. Remove salts and other contaminants by high-pressure fresh water cleaning. Clean damaged areas thoroughly. Improved surface preparation will improve the performance of the product. Use appropriate ZINAK Epoxy Primer for better performance. Mixing Instructions: Temperature of Zinak AQM53 Antifouling Paint must be 20°C/68°F or above at the time of mixing. Stir each component separately before blending. Mix three parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle. Application Conditions: Use only where application and curing can proceed at temperature above 10°C/50°F. Maximum relative humidity: 80%, preferably 40-60%. The temperature of the surface and that of the paint itself must also be above this limit. The optimal paint temperature for proper mixing, pumping and spraying is 15-25°C/59-77°F. In confined spaces provide adequate ventilation during application and drying. Application Process: Apply 2 coats per season on the hull. 3 coats are required on the leading and trailing edges, waterline, rudder and keel. This is important for the best performance. * Airless Spray: Graco 45:1 or 56:1 or equivalent. Tip Size: 0.021-0.025”. Thinning: 5% by volume with Hollywood Antifouling Epoxy Thinner. *Air Spray: Air cap with E tip and needle. Moisture trap should be used between air supply and pressure pot. Thinning: 5-10% by volume with Hollywood Antifouling Epoxy Thinner. *Brush or Roller: Low nap rollers. Thinning: 5% by volume with Hollywood Antifouling Epoxy Thinner. *Amount of thinning affected by temperature conditions. *Do not thin unless absolutely necessary. The occurrence of standing water or droplets on the painted surface immediately after application may result in discoloration. Use Hollywood Antifouling Epoxy Thinner to wash painting appliances, hoses and guns before and after use. Re-Coat Interval: 10°C (50°F) Minimum: 30 Hours - Maximum: 28 Days 20°C (68°F) Minimum: 10 Hours - Maximum: 20 Days 25°C (77°F) Minimum: 8 Hours - Maximum: 17 Days 30°C (86°F) Minimum: 5 Hours - Maximum: 14 Days Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion. All dust from sanding of blast roughening must be removed from the surface prior to the re-coat application. Avoid extra thinning for a better result. Safety Feature: Take precautions to avoid skin and eye contact. Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves, face masks etc. Proper ventilation and protective measures must be provided during applications and drying period to keep solvent vapor concentrations within safe limit. All work involving the application and use of this product should be performed in compliance with all relevant local and national, Health, Safety & Environmental standers and regulations. Do not discard this or pour paint into water courses. It is best to allow paints to harden before disposal. Precautions: * Away from the source of ignition and fire. * Keep away from direct sunlight, heat, and children. * Store in a well-ventilated location. * Stir well before use. * The container must be tightly closed when not in use. Pack Size: 4ltr and 20ltr. Shade Range: Red